For adults 18 and older. Ordering is not open yet.

Sleeve Studio

All on one page

Make your own sleeve: cheat sheet

Sleeve Studio quick guide. Prices checked November 17, 2026; they can change. Download the PDF

A design shown cut in half in Sleeve Studio

1Design it in Sleeve Studio

  • Open Sleeve Studio and pick a design. Turn the 3D view with your finger or mouse.
  • Fine-tune with the sliders: height, size and packing of the texture, from Mild to Extreme.
  • Build: Whole sleeve uses one design end to end. 4 sections lets you give each quarter its own design; section 1 is at the entrance.
  • Name your design and press Download. Building the mandrel file takes about a minute.
The printed white resin mandrel and plug

2Print the mandrel

  • The zip holds your mandrel STL, the plug STL, your design file and this guide.
  • Print both STLs in SLA resin. Not on a PLA or filament printer.
  • Print service: any online 3D printing service. Pick SLA resin, standard white, sanded finish.
  • Keep the mandrel under 59 C (138 F): no dishwasher, no hot water, no sun.

3What you need

ItemNotesPrice
Ecoflex 00-20, 2 lb trial unitThe one to start with. Much thinner to pour than 00-10, which makes it easy to get a clean pour.$33.44
Ecoflex 00-10, 2 lb trial unitThe softest. Very thick to pour: pour slowly, a vacuum chamber helps.$36.05
Ecoflex 00-31 Near Clear, trial unitNearly clear and the firmest of the three. About as firm as you want it, and still really good.$40.29
1.5 inch Schedule 40 PVC pipe, 2 ft: Amazon or any big-box home improvement store (example)One 2 ft length makes 3 molds. Cut to 200 mm (7-7/8 in).about $5
Vacuum chamber (optional): AmazonNot required, but a big help: fewer bubbles.
Mold release: petroleum jelly, or Ease Release 200Vaseline works great. Keep the coat thin.
From around the houseKitchen scale (grams), 2 plastic cups, stir sticks, painter's tape, nitrile gloves, a saw for the pipe, sandpaper, mild soap.

One 2 lb trial unit makes about 4 sleeves (about 200 g each).

Pipe plugged and taped; thin release coat on the mandrel

4Prep

  • Cut the pipe to 200 mm and sand the ends flat.
  • Thin film of petroleum jelly or release on the mandrel, the plug and inside the pipe.
  • Plug one end of the pipe and tape the joint.
  • Nitrile gloves only: latex and sulfur clay stop platinum silicone from curing.
Pouring into a window in the hat
Weighing A and B on a kitchen scale

5Mix and pour

  • Stir A and B in their jars. Weigh equal parts A and B: about 100 g each (your order card has the exact grams).
  • Mix 3 minutes, scraping sides and bottom. Pour into a second cup and mix 1 more minute.
  • Optional: vacuum the mixed cup until it rises and falls. Never vacuum the filled mold.
  • Brush silicone into the mandrel's pits. Set the mandrel in the pipe: end in the plug, hat on the pipe.
  • Pour a thin stream into one hat window until the mix stands in every window. Tap 20 times, wait 5 minutes, top up.
The finished silicone sleeve beside the mandrel and pipe
Pulling the mandrel out by its hat

6Cure, demold, care

  • Wait 4 hours at room temperature, above 65 F (18 C).
  • Remove tape and plug. Pull the mandrel by its hat, turning it on twisting designs.
  • Push the sleeve out from the closed end. Trim the thin rim ring.
  • Wash with mild soap and warm water. Dry, then dust with cornstarch. Use water-based lubricant only.